
That's not a skincare problem. It's a depth problem.
Your serum stops at 0.2mm. The sag starts at 4.
You've been consistent. Retinol at night, vitamin C in the morning, SPF without fail. Your skin looks well-kept and still, the jawline blurs a little more each year, the cheek sits a little lower, the fold beside your mouth stays put by lunchtime.
Nothing you're doing is wrong. It's just landing in the wrong place. Topicals work in the epidermis, roughly the top fifth of a millimetre.
Collagen. Muscle. Skin. One glide, all three.
LumiLift™ works where your skincare can't go.
Radiofrequency for the collagen layer. Microcurrent for the muscle beneath it. LED to finish. One glide, all three.
LumiLift stacks the three energy modalities aesthetic clinics actually use, and runs them through a single treatment head so they reach the skin together rather than in separate appointments,
Three layers. One pass.
Here's exactly what each technology is doing while the head is moving.
Most at-home devices pick one. A microcurrent tool works the muscle but never touches collagen. An LED mask calms the surface but does nothing structural. A single-mode RF wand warms the dermis but leaves the foundation slack.
Surface
Calms redness, settles the skin after energy work, drives serum absorption.
Structure
Controlled warming in the collagen-remodelling range — the layer that determines firmness.
Foundation
Low-level stimulation of the muscles that carry lift.
Loved by everyone, everywhere. Don't miss out.
Face Sculpt & V-Contour
Target the appearance of firmness and contour. This combination aims to support a more defined facial profile
Deep Firming & Wrinkle Smoothing
Help improve the appearance of fine lines and support skin firmness.
Purified Skin & Pore Clarity
Plasma + Blue / NIR LED generates a gentle, warm sensation. This process helps improve the appearance of pores and prepares the skin to better receive the benefits of your serum.
Instant Soothing & Calming
Help to provide a soothing sensation, which can help alleviate feelings of redness and sensitivity after treatment.
3,857+ people stopped booking sessions.
Why pay for four devices that each do one thing?
The maths that made us build this.
Works the muscle layer
Works the collagen layer
Surface calming + LED
Session time
Ongoing cost
LumiLift™
5 min
Gel only
Microcurrent device
5–10 min
Gel only
LED mask
10–20 min
None
You Might Also Wonder
Collapsible content
I already own a microcurrent device. Why would I need this?
I already own a microcurrent device. Why would I need this?
Because microcurrent only works one of the three layers. It stimulates facial muscle, which is genuinely useful but it does nothing to the collagen scaffold in the dermis, and that's what determines whether skin looks firm or slack. If your existing device stopped delivering after the first few months, that's why. LumiLift adds RF for the structural layer and LED to finish. Keep using both if you like; most people find they stop reaching for the single-mode one
Does the RF hurt?
Does the RF hurt?
No. It's warmth, not pain comparable to a hot stone held against the cheek. If it ever feels sharp or uncomfortable, you're low on gel or the intensity is set too high. Both are one-second fixes.
How often, realistically?
How often, realistically?
More is not better with RF; the collagen response needs recovery time between sessions.
Can I use it with fillers or Botox?
Can I use it with fillers or Botox?
Speak to whoever administered them first. RF heat can affect how some fillers behave, and the timing relative to your last treatment matters. This is a genuine "ask your practitioner" answer, not a hedge.
Do I have to buy your gel?
Do I have to buy your gel?
No. Any conductive gel works. Ours is unscented and formulated not to dry mid-session, which matters more than it sounds when you're eight minutes in but you're not locked in.